TaiShanPai/设备树/tspi-rk3566-user-v10-linux.dts

// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
/*
 * Copyright (c) 2020 Rockchip Electronics Co., Ltd.
 *
 */

 /*********************************************************************
 *           立创开发板不靠卖板赚钱，以培养中国工程师为己任  
 *         泰山派软硬件资料与相关扩展板软硬件资料官网全部开源
 *                      开发板官网：www.lckfb.com            
 *                     立创论坛：oshwhub.com/forum           
 *            关注B站：【立创开发板】，掌握我们的最新动态！  
 *********************************************************************
 * 文件名：tspi-rk3566-user-v10.dtsi
 * 描述：用户自定义层
 * 更新:
 * 时间          作者           联系           说明
 * 2023-09-13   吴才成    1378913492@qq.com   v1.0.0
 *********************************************************************/
/dts-v1/;

#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/display/media-bus-format.h>
#include <dt-bindings/pinctrl/rockchip.h>
#include "rk3566.dtsi"
#include <dt-bindings/display/rockchip_vop.h>


//tspi核心配置层，这里是几乎后期不需要怎么改动
#include "tspi-rk3566-core-v10.dtsi"

//【开/关】EDP 显示屏幕配置，用户可以基于此复制自己的屏幕，注意EDP与MIPI屏幕互斥，因为共用了VOP如果需要同显自行修改
// #include "tspi-rk3566-edp-v10.dtsi"

//【开/关】mipi 显示屏幕配置，用户可以基于此复制自己的屏幕，注意EDP与MIPI屏幕互斥，因为共用了VOP如果需要同显自行修改
// #include "tspi-rk3566-dsi-v10.dtsi"

//【开/关】HDMI 显示屏幕配置，里面内容几乎可以不用动，如果不需要hdmi显示直接注释掉即可
#include "tspi-rk3566-hdmi-v10.dtsi"

//【开/关】摄像头 目前视频的是ov5659
#include "tspi-rk3566-csi-v10.dtsi"

//【开/关】网口 扩展板上使用的是千兆网，不接扩展板情况下可以关闭
// #include "tspi-rk3566-gmac1-v10.dtsi"

//【开/关】下方是用户定义层，所有用户修改理论上在此下方修改就好了
/ {
	model = "lckfb tspi V10 Board";
	compatible = "lckfb,tspi-v10", "rockchip,rk3566";

	rk_headset: rk-headset {
		compatible = "rockchip_headset";
		headset_gpio = <&gpio0 RK_PC5 GPIO_ACTIVE_HIGH>;
		pinctrl-names = "default";
		pinctrl-0 = <&hp_det>;
	};

    mynode4 {

    };

	leds: leds {
		compatible = "gpio-leds";
		rgb_led_r: rgb-led-r {
			gpios = <&gpio1 RK_PB2 GPIO_ACTIVE_LOW>;
			linux,default-trigger = "timer";
			linux,delay-reg = <0>;   		// 延时注册
			linux,blink-delay-on = <500>; 	// 打开时间
			linux,blink-delay-off = <500>;	// 关闭时间
		};
		rgb_led_g: rgb-led-g {
			gpios = <&gpio1 RK_PB1 GPIO_ACTIVE_LOW>;
			linux,default-trigger = "timer";
			linux,delay-reg = <100>;   		// 延时注册
			linux,blink-delay-on = <1000>; 
			linux,blink-delay-off = <1000>;
		};
		rgb_led_b: rgb-led-b {
			gpios = <&gpio1 RK_PB0 GPIO_ACTIVE_LOW>;
			linux,default-trigger = "timer";
			linux,delay-reg = <100>;  		// 延时注册
			linux,blink-delay-on = <1500>; 
			linux,blink-delay-off = <1500>;
		};
	};

};

&pinctrl {
	headphone {
		hp_det: hp-det {
			rockchip,pins = <0 RK_PC5 RK_FUNC_GPIO &pcfg_pull_none>;
		};
	};
};

//用户三色灯
&leds {
	status = "okay";
};

//耳机插入检测，不使用扩展板情况需关闭，否则默认会检测到耳机插入
&rk_headset {
	status = "disabled";
};

//用户串口3
&uart3 {
	status = "okay";
	pinctrl-names = "default";
	pinctrl-0 = <&uart3m1_xfer>;
};

//用户I2C2
&i2c2 {
	status = "okay";

	/*添加你的I2C设备参考
	gt1x: gt1x@14 {
		compatible = "goodix,gt1x";
		reg = <0x14>;
		pinctrl-names = "default";
		pinctrl-0 = <&touch_gpio>;
		goodix,rst-gpio = <&gpio0 RK_PB6 GPIO_ACTIVE_HIGH>;
		goodix,irq-gpio = <&gpio0 RK_PB5 IRQ_TYPE_LEVEL_LOW>;
	};*/
};

&i2c3 {
	status = "okay";
	pinctrl-names = "default";
	pinctrl-0 = <&i2c3m1_xfer>;
	/*添加你的I2C设备参考
	gt1x: gt1x@14 {
		compatible = "goodix,gt1x";
		reg = <0x14>;
		pinctrl-names = "default";
		pinctrl-0 = <&touch_gpio>;
		goodix,rst-gpio = <&gpio0 RK_PB6 GPIO_ACTIVE_HIGH>;
		goodix,irq-gpio = <&gpio0 RK_PB5 IRQ_TYPE_LEVEL_LOW>;
	};*/
};


&spi3 {
	status = "okay";
	max-freq = <48000000>;
	dma-names = "tx","rx";
	pinctrl-names = "default", "high_speed";
	pinctrl-0 = <&spi3m1_cs0 &spi3m1_pins>;
	pinctrl-1 = <&spi3m1_cs0 &spi3m1_pins_hs>;
	spi_test@10 {
		compatible ="rockchip,spi_test_bus1_cs0";
		reg = <0>;
		spi-max-frequency = <24000000>;
		status = "okay";
	};
};

&pwm8 {
	status = "okay";
};

&pwm9 {
	status = "okay";
};

&pwm14 {
	status = "okay";
};

//pwd 15遥控器
&pwm15 {
	status = "okay";
	compatible = "rockchip,remotectl-pwm";
	remote_pwm_id = <3>;
	handle_cpu_id = <1>;
	remote_support_psci = <0>;
	pinctrl-names = "default";
	pinctrl-0 = <&pwm15m0_pins>;

	//用户自定方法：adb设置输出日志并通过dmesg确定usercode=address与key_table=command
	//echo 1 > sys/module/rockchip_pwm_remotectl/parameters/code_print
	//键值可在 include/dt-bindings/input/linux-event-codes.h 中查找
	ir_key1 {
		rockchip,usercode = <0xff00>;
		rockchip,key_table =
			<0xf2	KEY_MENU>,
			<0xe9	KEY_BACK>,
			<0xe3	KEY_ENTER>,
			<0xe7	KEY_UP>,
			<0xad	KEY_DOWN>,
			<0xf7	KEY_LEFT>,
			<0xa5	KEY_RIGHT>,
			<0xba	KEY_1>,
			<0xb9	KEY_2>,
			<0xb8	KEY_3>,
			<0xbb	KEY_4>,
			<0xbf	KEY_5>,
			<0xbc	KEY_6>,
			<0xf8	KEY_7>,
			<0xea	KEY_8>,
			<0xf6	KEY_9>,
			<0xe6	KEY_0>;
	};
};