改为外部时钟。添加gpioC13脚

Core/Inc/main.h

@@ -57,6 +57,8 @@ void Error_Handler(void);
 /* USER CODE END EFP */
 
 /* Private defines -----------------------------------------------------------*/
+#define Led_Pin GPIO_PIN_13
+#define Led_GPIO_Port GPIOC
 
 /* USER CODE BEGIN Private defines */
 

Core/Src/main.c

@@ -187,7 +187,6 @@ int main(void)
   while (1)
   {
     /* USER CODE END WHILE */
-
     /* USER CODE BEGIN 3 */
   }
   /* USER CODE END 3 */
@@ -205,10 +204,13 @@ void SystemClock_Config(void)
   /** Initializes the RCC Oscillators according to the specified parameters
   * in the RCC_OscInitTypeDef structure.
   */
-  RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSI;
+  RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;
+  RCC_OscInitStruct.HSEState = RCC_HSE_ON;
+  RCC_OscInitStruct.HSEPredivValue = RCC_HSE_PREDIV_DIV1;
   RCC_OscInitStruct.HSIState = RCC_HSI_ON;
-  RCC_OscInitStruct.HSICalibrationValue = RCC_HSICALIBRATION_DEFAULT;
-  RCC_OscInitStruct.PLL.PLLState = RCC_PLL_NONE;
+  RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
+  RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;
+  RCC_OscInitStruct.PLL.PLLMUL = RCC_PLL_MUL9;
   if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK)
   {
     Error_Handler();
@@ -218,12 +220,12 @@ void SystemClock_Config(void)
   */
   RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_HCLK|RCC_CLOCKTYPE_SYSCLK
                               |RCC_CLOCKTYPE_PCLK1|RCC_CLOCKTYPE_PCLK2;
-  RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_HSI;
+  RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
   RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
-  RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV1;
+  RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV2;
   RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV1;
 
-  if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_0) != HAL_OK)
+  if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_2) != HAL_OK)
   {
     Error_Handler();
   }
@@ -269,13 +271,26 @@ static void MX_USART1_UART_Init(void)
   */
 static void MX_GPIO_Init(void)
 {
+  GPIO_InitTypeDef GPIO_InitStruct = {0};
   /* USER CODE BEGIN MX_GPIO_Init_1 */
 
   /* USER CODE END MX_GPIO_Init_1 */
 
   /* GPIO Ports Clock Enable */
+  __HAL_RCC_GPIOC_CLK_ENABLE();
+  __HAL_RCC_GPIOD_CLK_ENABLE();
   __HAL_RCC_GPIOA_CLK_ENABLE();
 
+  /*Configure GPIO pin Output Level */
+  HAL_GPIO_WritePin(Led_GPIO_Port, Led_Pin, GPIO_PIN_RESET);
+
+  /*Configure GPIO pin : Led_Pin */
+  GPIO_InitStruct.Pin = Led_Pin;
+  GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
+  GPIO_InitStruct.Pull = GPIO_NOPULL;
+  GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;
+  HAL_GPIO_Init(Led_GPIO_Port, &GPIO_InitStruct);
+
   /* USER CODE BEGIN MX_GPIO_Init_2 */
 
   /* USER CODE END MX_GPIO_Init_2 */
@@ -299,7 +314,8 @@ void StartDefaultTask(void *argument)
   for(;;)
   {
     printf("Task_default\r\n");
-    osDelay(1000);
+    HAL_GPIO_TogglePin(GPIOC, GPIO_PIN_13);
+    osDelay(20);
   }
   /* USER CODE END 5 */
 }

rtos3.ioc

@@ -18,13 +18,16 @@ Mcu.IP4=USART1
 Mcu.IPNb=5
 Mcu.Name=STM32F103C(8-B)Tx
 Mcu.Package=LQFP48
-Mcu.Pin0=PA9
-Mcu.Pin1=PA10
-Mcu.Pin2=PA13
-Mcu.Pin3=PA14
-Mcu.Pin4=VP_FREERTOS_VS_CMSIS_V2
-Mcu.Pin5=VP_SYS_VS_Systick
-Mcu.PinsNb=6
+Mcu.Pin0=PC13-TAMPER-RTC
+Mcu.Pin1=PD0-OSC_IN
+Mcu.Pin2=PD1-OSC_OUT
+Mcu.Pin3=PA9
+Mcu.Pin4=PA10
+Mcu.Pin5=PA13
+Mcu.Pin6=PA14
+Mcu.Pin7=VP_FREERTOS_VS_CMSIS_V2
+Mcu.Pin8=VP_SYS_VS_Systick
+Mcu.PinsNb=9
 Mcu.ThirdPartyNb=0
 Mcu.UserConstants=
 Mcu.UserName=STM32F103C8Tx
@@ -52,6 +55,14 @@ PA14.Mode=Serial_Wire
 PA14.Signal=SYS_JTCK-SWCLK
 PA9.Mode=Asynchronous
 PA9.Signal=USART1_TX
+PC13-TAMPER-RTC.GPIOParameters=GPIO_Label
+PC13-TAMPER-RTC.GPIO_Label=Led
+PC13-TAMPER-RTC.Locked=true
+PC13-TAMPER-RTC.Signal=GPIO_Output
+PD0-OSC_IN.Mode=HSE-External-Oscillator
+PD0-OSC_IN.Signal=RCC_OSC_IN
+PD1-OSC_OUT.Mode=HSE-External-Oscillator
+PD1-OSC_OUT.Signal=RCC_OSC_OUT
 PinOutPanel.RotationAngle=0
 ProjectManager.AskForMigrate=true
 ProjectManager.BackupPrevious=false
@@ -85,13 +96,27 @@ ProjectManager.UAScriptAfterPath=
 ProjectManager.UAScriptBeforePath=
 ProjectManager.UnderRoot=false
 ProjectManager.functionlistsort=1-SystemClock_Config-RCC-false-HAL-false,2-MX_GPIO_Init-GPIO-false-HAL-true,3-MX_USART1_UART_Init-USART1-false-HAL-true
-RCC.APB1Freq_Value=8000000
-RCC.APB2Freq_Value=8000000
+RCC.ADCFreqValue=36000000
+RCC.AHBFreq_Value=72000000
+RCC.APB1CLKDivider=RCC_HCLK_DIV2
+RCC.APB1Freq_Value=36000000
+RCC.APB1TimFreq_Value=72000000
+RCC.APB2Freq_Value=72000000
+RCC.APB2TimFreq_Value=72000000
+RCC.FCLKCortexFreq_Value=72000000
 RCC.FamilyName=M
-RCC.IPParameters=APB1Freq_Value,APB2Freq_Value,FamilyName,PLLCLKFreq_Value,PLLMCOFreq_Value,TimSysFreq_Value
-RCC.PLLCLKFreq_Value=8000000
-RCC.PLLMCOFreq_Value=4000000
-RCC.TimSysFreq_Value=8000000
+RCC.HCLKFreq_Value=72000000
+RCC.IPParameters=ADCFreqValue,AHBFreq_Value,APB1CLKDivider,APB1Freq_Value,APB1TimFreq_Value,APB2Freq_Value,APB2TimFreq_Value,FCLKCortexFreq_Value,FamilyName,HCLKFreq_Value,MCOFreq_Value,PLLCLKFreq_Value,PLLMCOFreq_Value,PLLMUL,PLLSourceVirtual,SYSCLKFreq_VALUE,SYSCLKSource,TimSysFreq_Value,USBFreq_Value,VCOOutput2Freq_Value
+RCC.MCOFreq_Value=72000000
+RCC.PLLCLKFreq_Value=72000000
+RCC.PLLMCOFreq_Value=36000000
+RCC.PLLMUL=RCC_PLL_MUL9
+RCC.PLLSourceVirtual=RCC_PLLSOURCE_HSE
+RCC.SYSCLKFreq_VALUE=72000000
+RCC.SYSCLKSource=RCC_SYSCLKSOURCE_PLLCLK
+RCC.TimSysFreq_Value=72000000
+RCC.USBFreq_Value=72000000
+RCC.VCOOutput2Freq_Value=8000000
 USART1.IPParameters=VirtualMode
 USART1.VirtualMode=VM_ASYNC
 VP_FREERTOS_VS_CMSIS_V2.Mode=CMSIS_V2
@@ -99,3 +124,4 @@ VP_FREERTOS_VS_CMSIS_V2.Signal=FREERTOS_VS_CMSIS_V2
 VP_SYS_VS_Systick.Mode=SysTick
 VP_SYS_VS_Systick.Signal=SYS_VS_Systick
 board=custom
+rtos.0.ip=FREERTOS